Emboss Tape
BH CONNECTOR
H
J
S
T
4.0/8.0/12.0mm pitch/Disconnectable Crimp style connectors
Specifications –––––––––––––––––––
• Current rating: 1.0A AC, DC (AWG #22)
• Voltage rating: 600V AC, DC
• Temperature range: -25˚C to +85˚C
(including temperature rise in applying
electrical current)
• Contact resistance: Initial value/10m Ω max.
After environmental testing/20m Ω max.
• Insulation resistance:
1,000M Ω min.
• Withstanding voltage: 1,800V AC/minute
• Applicable wire: AWG #28 to #22
* Compliant with RoHS.
* Refer to "General Instruction and Notice when using
Terminals and Connectors" at the end of this catalog.
* Contact JST for details.
1
H
2
J
S
T
3
Low profile connectors with high
withstanding voltage, designed for
connecting liquid crystal display back light
lamps to their starters.
• Low profile
• SMT configuration
• Applicable to special wires
• Headers with locating bosses
• Housing lock also serves as polarizing device
Standards ––––––––––––––––––––––
0
Recognized E60389
1 Certified LR20812
PC board layout (viewed from component side)
SMT type
(2 circuits 4mm pitch)
(2 1 7
circuits 8mm pitch)
12 ±0.1
1.5 ±0.1
1.7 ±0.1
12
3.4±0.1
0.2
9 min
1.7 ±0.1
Through-hole type
16 ±0.1
22
12
1.85
±0.05
9 min
6.4
±0.1
0.2
3.4 ±0.1
9 min
6.4 ±0.1
9 min
9 min
6.4 ±0.1
1.5 ±0.1
1 min
6.4 ±0.1
0.2
3.4 ±0.1
6.4 ±0.1
12 ±0.1
4 ±0.1
19-2
1.7 ±0.1
4-4
2
±0.05
±0.05
8±0.05
φ0.7 +0.1
0
φ0.9+0.1
0
4 ±0.1
4 ±0.1
1.7 ±0.1
0.2
(3 circuits 4mm pitch plugged up)
(4 circuits 4mm pitch with post removed)
24
12 ±0.1
1min
1.5 ±0.1
3.4±0.1
9 min
6.4 ±0.1
1.4 ±0.1
0.2
3.4 ±0.1
0.2
3.4 ±0.1
9 min
6.4 ±0.1
1.5 ±0.1
(4 circuits 4mm pitch)
20
1.7 ±0.1
1min
1.7 ±0.1
4-4
1.5 ±0.1
1.7 ±0.1
8 ±0.1
4 ± 0.1
19
1 min
1.5 ±0.1
9 min
1.5 ±0.1
1min
0.2
3.4 ±0.1
18
+0.1
φ 0
0.9
(3 circuits 4mm pitch)
±0.1
8 ±0.1
1 min
8 ±0.1
1min
1.7 ±0.1
(2 circuits 12mm pitch)
2-12
2 ±0.1
0.2
3.4 ±0.1
9 min
6.4 ±0.1
8 ±0.1
1 min
0.2
3.4 ±0.1
4 ±0.1
1 min
1.5 ±0.1
1 7circuits 8mm pitch plugged up)
(2
(2 circuits 8mm pitch with bosses)
6.4 ±0.1
2-4
1.5 ±0.1
1.7 ±0.1
Note: 1. Tolerances are for pattern non-cumulative: ±0.05mm for all centers. Tolerance for hole size is ±0.1.
2. Hole dimensions differ according to the kind of PC board and piercing method. The dimensions above should serve as guideline. Contact JST for details.
1