Transceiver
Solutions
Alaska® Single-Port
Gigabit Ethernet Transceiver
88E1111
PRODUCT OVERVIEW
The Marvell¨ Alaska¨ family of Gigabit Ethernet (GbE) over copper transceivers are the industryÕs lowest power,
smallest form factor, highest performance, and highest port density solutions in volume production. The Alaska
single-port 88E1111 transceiver leads the industry with the lowest power consumption (only 0.75W), as well as
the smallest package footprint option Ñ only 9 mm x 9 mm. The Alaska single-port 88E1111 product performs all
of the physical layer (PHY) functions for half- and full-duplex 10BASE-T Ethernet on CAT 3, 4 and 5 cable, and
half- and full-duplex 100BASE-TX and 1000BASE-T Ethernet on CAT 5 twisted pair cable. Additionally, the 88E1111
device offers additional support of 1000BASE-X through an integrated 1.25 GHz Serializer/Deserializer (SERDES).
D/A
Waveshape
Filter
P0_MDC
P0_MDIO
P0_INTn
P0_RSET
P0_HSDACP/N
P0_TSTPT
A/D
Skew
Control
Fiber/SERDES
Transmit
Trellis
Decoder
Near End
Crosstalk
Canceller
Feed
Forward
Equalizer
Decision
Feedback
Equalizer
DPLL
Management
Interface
Registers
Bias/Test
Auto-Negotiation
LED/
ConÞguration
P0_LED_LINK10
P0_LED_LINK100
P0_LED_LINK1000
P0_LED_DUPLEX
P0_LED_RX
P0_LED_TX
GCONFIG[1:0]
JTAG
P0_TX_CTL
P0_TXD[3:0]
P0_GTX_CLK
P0_S_IN+/P0_S_CLK+/P0_S_OUT+/-
10/100/1000
Receive PCS
Echo
Canceller
Timing
Control
Active Hybrid
Gain Control
Baseline
10BASE-T
Receiver
10/100/1000
Transmit PCS
P0_RX_CTL
P0_RXD[3:0]
P0_RX_CLK
TRST#
TCK
TDI
TMS
TDO
Clock/Reset
XTAL1
XTAL2
RESETn
125CLK
Fig 1. Alaska Single-Port GbE Transceiver (88E1111) Block Diagram
FEATURES
¥ Ultra low power, only 0.75W
¥ 10/100/1000BASE-T IEEE 802.3 compliant
¥ Supports GMII/RGMII/SGMII/TBI/RTBI interfaces
¥ Virtual Cable Testerª (VCT) feature
¥ Integrated 1.25 GHz SERDES
¥ Media Detect feature automatically detects and conÞgures to either
copper or Þber media
¥ GBIC/SFP mode
¥ Automatic support for 2-pair CAT 5 cable (100 Mbps)
¥ Power management modes
¥ Four RGMII timing modes
¥ Operation up to 180 meters CAT 5 cable
¥ Auto-MDI/MDIX crossover for all modes of operation
¥ Support IEEE 1149.1 (JTAG) and NAND-tree ICT
¥ Advanced mixed-signal and DSP techniques
BENEFITS
¥ Enables higher integration and reduced system cost
¥ Compatibility with existing installed base of compliant devices
¥ Reduces cost and simpliÞes PCB layout
¥ IdentiÞcation and isolation of cable faults
¥ Supports 1000BASE-X Þber applications
¥ Complete media ßexibility
¥
¥
¥
¥
¥
¥
¥
¥
Supports plug-and-play GBIC and SFP modules
Operates over installed 2-pair cable
Reduced system power
Eliminate the need for on-board delay lines
Functions over a wider base of cabling infrastructures
Eases installation and reduces cost
SimpliÞes board level testing/debugging
Advanced DSP design